FUJITSU-SIEMENS ESPRIMO P2520/ C 430/ 1GB/ 80GB 7.2k/ DVD

Podpora:	kompletní
Ovladač:	v jádře

Technické parametry

Procesor:
Socket LGA 775, Intel Celeron 430 s frekvencí 1,8 GHz
512 KB L2 Cache 
FSB 800 MHz

Čipset:
NVIDIA GeForce 7050  

Paměť:
1 GB DDR2 667 MHz
2 sloty pro max. 4 GB

Grafická karta:
Integrovaná NVIDIA GeForce 7050 s až 128 MB sdílené paměti

Pevný disk:
80 GB, 7200 RPM
Rozhraní Serial ATA II

Mechanika:
DVD-ROM

Audio:
Integrovaný zvukový kodek Realtek ALC262

Komunikace:
Integrovaná síťová karta 10/100/1000 Mbit/s Realtek RTL 8211B

Rozšiřující sloty:
2 x PCI
1 x PCI Express 16x

Rozšiřující pozice:
1 x 3,5" externí
2 x 5,25" externí
1 x 3,5" interní

Vstupy a výstupy: 
1 x Sériový port
1 x VGA
2 x Mikrofon (vpředu a vzadu)
2 x Sluchátka (vpředu a vzadu)
1 x Line in
1 x RJ-45 
8 x USB 2.0 (2 vpředu, 6 vzadu)

Identifikace pod Linuxem

Thor:/home/evzen# lspci
00:00.0 Host bridge: nVidia Corporation Device 07c2 (rev a2)
00:00.1 RAM memory: nVidia Corporation nForce 630i memory controller (rev a2)
00:01.0 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.1 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.2 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.3 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.4 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.5 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:01.6 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:02.0 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1)
00:03.0 ISA bridge: nVidia Corporation Device 07d7 (rev a2)
00:03.1 SMBus: nVidia Corporation Device 07d8 (rev a1)
00:03.4 RAM memory: nVidia Corporation Device 07c8 (rev a1)
00:04.0 USB Controller: nVidia Corporation GeForce 7100/nForce 630i (rev a1)
00:04.1 USB Controller: nVidia Corporation GeForce 7100/nForce 630i (rev a1)
00:09.0 Audio device: nVidia Corporation MCP73 High Definition Audio (rev a1)
00:0a.0 PCI bridge: nVidia Corporation Device 056d (rev a1)
00:0b.0 PCI bridge: nVidia Corporation Device 056e (rev a1)
00:0c.0 PCI bridge: nVidia Corporation Device 056f (rev a1)
00:0d.0 PCI bridge: nVidia Corporation Device 056f (rev a1)
00:0e.0 IDE interface: nVidia Corporation Device 07f0 (rev a2)
00:0f.0 Ethernet controller: nVidia Corporation MCP73 Ethernet (rev a2)
00:10.0 VGA compatible controller: nVidia Corporation Device 07e2 (rev a2)
Thor:/home/evzen# lsmod
Module                  Size  Used by
nls_iso8859_1           4128  1
nls_cp437               5792  1
vfat                   12224  1
fat                    48764  1 vfat
usb_storage            77664  1
ipv6                  240836  14
ppdev                   8804  0
parport_pc             33668  0
lp                     11076  0
parport                34280  3 ppdev,parport_pc,lp
dock                   10384  0
ac                      6116  0
sbs                    14376  0
sbshc                   6848  1 sbs
video                  18672  0
output                  3744  1 video
battery                13572  0
loop                   16804  0
snd_hda_intel         275392  7
snd_pcm_oss            38272  0
snd_pcm                71780  4 snd_hda_intel,snd_pcm_oss
snd_mixer_oss          15296  1 snd_pcm_oss
snd_seq_dummy           3780  0
snd_seq_oss            29472  0
psmouse                36464  0
snd_seq_midi            8160  0
serio_raw               6660  0
pcspkr                  3200  0
snd_rawmidi            22624  1 snd_seq_midi
rtc                    13052  0
snd_seq_midi_event      6976  2 snd_seq_oss,snd_seq_midi
snd_seq                46544  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_m
idi_event
snd_timer              21092  4 snd_pcm,snd_seq
snd_seq_device          7820  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmi
di,snd_seq
snd                    48612  19 snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss
,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore               7552  1 snd
snd_page_alloc         10056  2 snd_hda_intel,snd_pcm
container               4864  0
button                  8432  0
evdev                  11104  4
ext3                  122920  2
jbd                    43732  1 ext3
mbcache                 8288  1 ext3
sg                     33264  0
sr_mod                 16708  0
cdrom                  32512  1 sr_mod
sd_mod                 27200  5
usbhid                 28096  0
hid                    34272  1 usbhid
ahci                   26212  3
ata_generic             7428  0
libata                144624  2 ahci,ata_generic
scsi_mod              141164  5 usb_storage,sg,sr_mod,sd_mod,libata
forcedeth              46828  0
generic                 4388  0 [permanent]
ide_core              108292  1 generic
ehci_hcd               32524  0
ohci_hcd               21988  0
usbcore               133004  5 usb_storage,usbhid,ehci_hcd,ohci_hcd
thermal                16028  0
processor              36552  1 thermal
fan                     4772  0

Thor:/home/evzen# dmesg
Initializing cgroup subsys cpuset
Linux version 2.6.24-1-686 (Debian 2.6.24-7) (dannf@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Thu May 8 02:16:39 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
 BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002ffe0000 (usable)
 BIOS-e820: 000000002ffe0000 - 000000002ffe5000 (ACPI data)
 BIOS-e820: 000000002ffe5000 - 000000002ffe6000 (ACPI NVS)
 BIOS-e820: 000000002ffe6000 - 0000000038000000 (reserved)
 BIOS-e820: 0000000038000000 - 000000003ff00000 (usable)
 BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f8350
Entering add_active_range(0, 0, 261888) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   261888
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   261888
On node 0 totalpages: 261888
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 254 pages used for memmap
  HighMem zone: 32258 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F8320, 0014 (r0 PTLTD )
ACPI: RSDT 2FFE2E03, 0038 (r1 PTLTD    RSDT      60000  LTP        0)
ACPI: FACP 2FFE4E8C, 0074 (r1 FSC                60000         F4240)
ACPI: DSDT 2FFE2E3B, 2051 (r1 FSC    D2740/A1    60000 MSFT  3000001)
ACPI: FACS 2FFE5FC0, 0040
ACPI: MCFG 2FFE4F00, 003C (r1 PTLTD    MCFG      60000  LTP        0)
ACPI: HPET 2FFE4F3C, 0038 (r1 PTLTD  HPETTBL     60000  LTP        1)
ACPI: APIC 2FFE4F74, 0064 (r1 PTLTD      APIC      60000  LTP        0)
ACPI: BOOT 2FFE4FD8, 0028 (r1 PTLTD  $SBFTBL$    60000  LTP        1)
ACPI: DMI detected: Fujitsu Siemens
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 7:6 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:b8000000)
swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000ce000
swsusp: Registered nosave memory region: 00000000000ce000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
swsusp: Registered nosave memory region: 000000002ffe0000 - 000000002ffe5000
swsusp: Registered nosave memory region: 000000002ffe5000 - 000000002ffe6000
swsusp: Registered nosave memory region: 000000002ffe6000 - 0000000038000000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259842
Kernel command line: root=/dev/sda1 ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1799.992 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 897096k/1047552k available (1786k kernel code, 18500k reserved, 714k data, 248k init, 130048k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0377000 - 0xc03b5000   ( 248 kB)
      .data : 0xc02beaf9 - 0xc0371384   ( 714 kB)
      .text : 0xc0100000 - 0xc02beaf9   (1786 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet clockevent registered
Calibrating delay using timer specific routine.. 3603.95 BogoMIPS (lpj=7207911)
Security Framework initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: afebfbff 20100000 00000000 00000000 0000e31d 00000000 00000001 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
CPU: After all inits, caps: afebfbff 20100000 00000000 00003940 0000e31d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Celeron(R) CPU          430  @ 1.80GHz stepping 01
Total of 1 processors activated (3603.95 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:0a.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *5
ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNKQ] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LNKR] (IRQs 16 17 18 19 20 21 22 23) *0
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 8 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x1000-0x10e7 has been reserved
system 00:01: ioport range 0x1400-0x14fe has been reserved
system 00:01: ioport range 0x1800-0x18fe has been reserved
system 00:01: ioport range 0x1900-0x19fe has been reserved
system 00:01: ioport range 0x1a00-0x1afe has been reserved
system 00:01: ioport range 0x1b00-0x1b0e has been reserved
system 00:01: ioport range 0x1c00-0x1cfe has been reserved
system 00:01: ioport range 0xfe00-0xfe00 has been reserved
system 00:01: ioport range 0xff00-0xff00 has been reserved
system 00:01: iomem range 0xf8000000-0xfbffffff could not be reserved
system 00:01: iomem range 0xfec00000-0xfecfffff could not be reserved
system 00:01: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:01: iomem range 0xfef80000-0xfef80fff has been reserved
PCI: Bridge: 0000:00:0a.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0a.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
 it is
Freeing initrd memory: 6375k freed
Simple Boot Flag at 0x3b set to 0x1
audit: initializing netlink socket (disabled)
audit(1213704977.816:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:10.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 248k freed
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LNKJ] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKJ] -> GSI 23 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:04.0: irq 16, io mem 0xfe206000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LNKI] -> GSI 22 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 17, io mem 0xfe208000
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LNKL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKL] -> GSI 21 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0f.0 to 64
SCSI subsystem initialized
libata version 3.00 loaded.
forcedeth 0000:00:0f.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:19:99:2c:5c:58
forcedeth 0000:00:0f.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
ahci 0000:00:0e.0: version 3.0
ACPI: PCI Interrupt Link [LNKN] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKN] -> GSI 20 (level, high) -> IRQ 19
usb 1-5: new low speed USB device using ohci_hcd and address 2
usb 1-5: configuration #1 chosen from 1 choice
usb 1-6: new low speed USB device using ohci_hcd and address 3
ahci 0000:00:0e.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
ahci 0000:00:0e.0: flags: 64bit sntf led clo pmp pio
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m8192@0xfe204000 port 0xfe204100 irq 220
ata2: SATA max UDMA/133 abar m8192@0xfe204000 port 0xfe204180 irq 220
ata3: SATA max UDMA/133 abar m8192@0xfe204000 port 0xfe204200 irq 220
ata4: SATA max UDMA/133 abar m8192@0xfe204000 port 0xfe204280 irq 220
usb 1-6: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input:   USB Keyboard as /class/input/input0
input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:04.0-5
input:   USB Keyboard as /class/input/input1
input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:04.0-5
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2
input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:04.0-6
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: WDC WD800JD-55MUA1, 10.01E01, max UDMA/133
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0F04, max UDMA/100
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      WDC WD800JD-55MU 10.0 PQ: 0 ANSI: 5
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDRH20N  0F04 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 <<4>Driver 'sr' needs updating - please use bus_type methods
 sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5
Attempting manual resume
swsusp: Marking nosave pages: 000000000009d000 - 0000000000100000
swsusp: Marking nosave pages: 000000002ffe0000 - 0000000038000000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input5
ACPI: PCI Interrupt Link [LNKM] enabled at IRQ 19
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKM] -> GSI 19 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:09.0 to 64
hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
Adding 2273156k swap on /dev/sda5.  Priority:-1 extents:1 across:2273156k
EXT3 FS on sda1, internal journal
loop: module loaded
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: no link during initialization.
No dock devices found.
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
usb 2-7: new high speed USB device using ehci_hcd and address 4
usb 2-7: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access     ChipsBnk Flash Disk       4.00 PQ: 0 ANSI: 2
sd 4:0:0:0: [sdb] 997119 2048-byte hardware sectors (2042 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] 997119 2048-byte hardware sectors (2042 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
 sdb: unknown partition table
sd 4:0:0:0: [sdb] Attached SCSI removable disk
sd 4:0:0:0: Attached scsi generic sg2 type 0
Thor:/home/evzen#                         

Postup zprovoznění pod Linuxem

Tento počítač jsem zprovoznil distribucí Debian Lenny(testing),
s Etch(stable) se ani nepokoušejte instalovat nemá podporu 
chipset integrovaná síťovka  ani integrovaná zvukovka a grafika .
S Lenny funguje vše jen je potíž z grafikou musí se instalovat driver
já jsem ho neistaloval nebyla potřeba vyřešil jsem to pomocí  vesa funguje
 to bez problému. Jinak nvidia má podporu na stránkách. 

Dokument vytvořil: odyn, 17.6.2008 15:06 | Zobrazeno: 2627×