/dev/sde: ATA device, with non-removable media Model Number: ST3000DM001-1E6166 Serial Number: W1F4AT8B Firmware Revision: SC48 Transport: Serial, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x0029) Supported: 8 7 6 5 Likely used: 8 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 5860533168 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 2861588 MBytes device size with M = 1000*1000: 3000592 MBytes (3000 GB) cache/buffer size = unknown Form Factor: 3.5 inch Nominal Media Rotation Rate: 7200 Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: 128 Recommended acoustic management value: 208, current value: 0 DMA: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5 udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE * Advanced Power Management feature set SET_MAX security extension * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Phy event counters * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set unknown 206[7] unknown 206[12] (vendor specific) unknown 206[13] (vendor specific) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 350min for SECURITY ERASE UNIT. 350min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 5000c5006e6c085c NAA : 5 IEEE OUI : 000c50 Unique ID : 06e6c085c Checksum: correct smartctl 7.2 2021-09-14 r5237 [x86_64-linux-5.3.18-150300.59.87-default] (SUSE RPM) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1E6166 Serial Number: W1F4AT8B LU WWN Device Id: 5 000c50 06e6c085c Firmware Version: SC48 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Aug 12 22:19:11 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 366) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3081) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 071 071 006 Pre-fail Always - 13038448 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3165 5 Reallocated_Sector_Ct 0x0033 096 096 010 Pre-fail Always - 3928 7 Seek_Error_Rate 0x000f 054 052 030 Pre-fail Always - 81608111465 9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 24428 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1492 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 4638 188 Command_Timeout 0x0032 100 061 000 Old_age Always - 19 20 75 189 High_Fly_Writes 0x003a 082 082 000 Old_age Always - 18 190 Airflow_Temperature_Cel 0x0022 075 038 045 Old_age Always In_the_past 25 (5 100 25 21 0) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 879 193 Load_Cycle_Count 0x0032 062 062 000 Old_age Always - 76686 194 Temperature_Celsius 0x0022 025 062 000 Old_age Always - 25 (0 8 0 0 0) 197 Current_Pending_Sector 0x0012 100 094 000 Old_age Always - 120 198 Offline_Uncorrectable 0x0010 100 094 000 Old_age Offline - 120 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1681h+28m+15.803s 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 23248751032 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 28055753543 SMART Error Log Version: 1 ATA Error Count: 6906 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6906 occurred at disk power-on lifetime: 24427 hours (1017 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 30 23 5e 00 Error: UNC at LBA = 0x005e2330 = 6169392 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 30 23 5e 40 00 00:56:04.187 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.136 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.086 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.032 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.992 READ DMA EXT Error 6905 occurred at disk power-on lifetime: 24427 hours (1017 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 30 23 5e 00 Error: UNC at LBA = 0x005e2330 = 6169392 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 30 23 5e 40 00 00:56:04.187 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.136 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.086 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.032 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.992 READ DMA EXT Error 6904 occurred at disk power-on lifetime: 24427 hours (1017 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 30 23 5e 00 Error: UNC at LBA = 0x005e2330 = 6169392 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 30 23 5e 40 00 00:56:04.136 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.086 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.032 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.992 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.978 READ DMA EXT Error 6903 occurred at disk power-on lifetime: 24427 hours (1017 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 30 23 5e 00 Error: UNC at LBA = 0x005e2330 = 6169392 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 30 23 5e 40 00 00:56:04.136 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.086 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.032 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.992 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.978 READ DMA EXT Error 6902 occurred at disk power-on lifetime: 24427 hours (1017 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 30 23 5e 00 Error: UNC at LBA = 0x005e2330 = 6169392 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 30 23 5e 40 00 00:56:04.086 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:04.032 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.992 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.978 READ DMA EXT 25 00 08 30 23 5e 40 00 00:56:03.872 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 70% 24330 - # 2 Extended offline Completed: read failure 90% 24007 - # 3 Short offline Completed without error 00% 21365 - # 4 Short offline Completed without error 00% 21341 - # 5 Short offline Completed without error 00% 21317 - # 6 Short offline Completed without error 00% 20919 - # 7 Short offline Completed without error 00% 20895 - # 8 Short offline Completed without error 00% 20870 - # 9 Short offline Completed without error 00% 20855 - #10 Short offline Completed without error 00% 20728 - #11 Short offline Completed without error 00% 20704 - #12 Short offline Completed without error 00% 20680 - #13 Short offline Completed without error 00% 20656 - #14 Short offline Completed without error 00% 20632 - #15 Short offline Completed without error 00% 20608 - #16 Short offline Completed without error 00% 20584 - #17 Short offline Completed without error 00% 20560 - #18 Short offline Completed without error 00% 20536 - #19 Short offline Completed without error 00% 20512 - #20 Short offline Completed without error 00% 20488 - #21 Short offline Completed without error 00% 20464 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Disk /dev/sde: 2.73 TiB, 3000592977920 bytes, 732566645 sectors Disk model: D3 Station Units: sectors of 1 * 4096 = 4096 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disklabel type: dos Disk identifier: 0x4a73c41f Device Boot Start End Sectors Size Id Type /dev/sde1 * 64 732564063 732564000 2.7T 7 HPFS/NTFS/exFAT