HP 712/100

HP712/100 - obsahuje 100MHz CPU PA-7100LC, 32-192MB RAM (ECC SIMM-72) a 260MB-2GB SCSI-2 disk (podle neoficiálních zdrojů lze připojit až 9.1GB SCSI-2 disk). Vzadu vystupují konektory VGA, sériový, paralelní, LineOut+Mic,2xPS/2, RJ45+AUI a Cannon MD50 pro SCSI-2 externí zařízení. Case je formátu pizza-box, na poměrně malé základní desce je integrován zvukový chip HP Harmony, síťový adaptér Intel82596 a SCSI adaptér NCR 53c700.

Podarilo se mi zprovoznit 2x 4.3GB SCSI-2 HDD, nastaveni SCSI je ID.6 a ID.5, pak lze vybrat, z jakeho disku se bude bootovsat, doporuceno je ID.6 - nainstalujte OS na ID.6 a data nechte na ID.5, s maximalni kapacitou HDD (9.1GB) dostanete 18GB prostoru

Výpis z dmesg:

klogd 1.4.1#10, log source = /proc/kmsg started.
Inspecting /boot/System.map-2.4.17-32
Loaded 30501 symbols from /boot/System.map-2.4.17-32.
Symbols match kernel version 2.4.17.
No module symbols loaded.
Linux version 2.4.17-32 (root@paer) (gcc version 3.0.4) #1 Sat Mar 16 17:09:00 MST 2002
FP[0] enabled: Rev 1 Model 13
The 32-bit Kernel has started...
Determining PDC firmware type: Snake.
model 00006020 00000481 00000000 00000000 779af008 00000000 00000004 00000072 00000072
vers  0000000c
model 9000/712
Total Memory: 128 Mb
pagetable_init
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sda3 HOME=/ console=tty0 sti=1 sti_font=VGA8x16 TERM=linux palo
_kernel=3/boot/vmlinux
Console: colour dummy device 160x64
Calibrating delay loop... 99.73 BogoMIPS
Memory: 125976k available
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Searching for devices...
Found devices:

1. Gecko 100 GSC Core Graphics (10) at 0xf8000000 [1], versions 0x1d, 0x0, 0x85
2. Gecko 100 Core BA (11) at 0xf0100000 [2], versions 0x1d, 0x0, 0x81
3. Gecko 100 Core SCSI (10) at 0xf0106000 [2/0/1], versions 0x1d, 0x0, 0x82
4. Gecko 100 Core LAN (802.3) (10) at 0xf0107000 [2/0/2], versions 0x1d, 0x0, 0x8a
5. Gecko 100 Core RS-232 (10) at 0xf0105000 [2/0/4], versions 0x1d, 0x0, 0x8c
6. Gecko 100 Core Centronics (10) at 0xf0102000 [2/0/6], versions 0x1d, 0x0, 0x74
7. Gecko 100 Audio (10) at 0xf0104000 [2/0/8], versions 0x1d, 0x0, 0x7b
8. Gecko 100 Core PC Floppy (10) at 0xf010a000 [2/0/10], versions 0x1d, 0x0, 0x83
9. Gecko 100 Core PS/2 Port (10) at 0xf0108000 [2/0/11], versions 0x1d, 0x0, 0x84
10. Gecko 100 Core PS/2 Port (10) at 0xf0108100 [2/0/12], versions 0x1d, 0x0, 0x84
11. Gecko 100 (712/100) (0) at 0xfffbe000 [8], versions 0x602, 0x0, 0x4
12. Memory (1) at 0xfffbf000 [9], versions 0x39, 0x0, 0x9
CPU(s): 1 x PA7100LC (PCX-L) at 100.000000 MHz
Lasi version 0 at 0xf0100000 found.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Enabled gecko-style soft power switch.
Starting kswapd
Journalled Block Device driver loaded
parport_init_chip: initialize bidirectional-mode.
parport0: PC-style at 0xf0102800, irq 88 [PCSPP,TRISTATE]
STI word mode ROM at f0080000, hpa=f8000000
STI word mode ROM, id 2b4ded6d-40a00499, conforms to spec rev. 8.04
STI device: HPA208LC1024
Console: switching to colour frame buffer device 128x48
fb0: stifb 1024x768-8 frame buffer device, id: 2b4ded6d, mmio: 0xf8100000
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at iomem 0xf0105800 (irq = 90) is a 16550A
PS/2 keyboard port at 0xf0108000 (irq 69) found, device attached.
PS/2 psaux port at 0xf0108100 (irq 69) found, device attached.
lp0: using parport0 (interrupt-driven).
Generic RTC Driver v1.02 05/27/1999 Sam Creasey (sammy@oh.verio.com)
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
loop: loaded (max 8 devices)
Found i82596 at 0xf0107000, IRQ 87
eth0: 82596 at 0xf0107000, 00 60 B0 80 C5 56 IRQ 87.
82596.c $Revision: 1.28 $
SCSI subsystem driver Revision: 1.00
53c700: Version 2.6 By James.Bottomley@HansenPartnership.com
scsi0: 53c710 rev 2 
scsi0 : LASI SCSI 53c700
scsi0: (6:0) Synchronous at offset 8, period 100ns
   Vendor: DEC       Model: DSP3107LS         Rev: X441
   Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
scsi0: (6:0) Enabling Tag Command Queuing
SCSI device sda: 2091144 512-byte hdwr sectors (1071 MB)
Partition check:
sda: sda1 sda2 sda3
Lasi Harmony Audio driver V0.9a, h/w id 20, rev. 18 at 0xf0104000, IRQ 82
sticonsole_init: searching for STI ROMs
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 190k freed
Adding Swap: 124924k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
Found i82596 at 0xf0107000, IRQ 87
divert: allocating divert_blk for eth0
eth0: 82596 at 0xf0107000, 00 60 B0 80 C5 56 IRQ 87.
82596.c $Revision: 1.32 $
Lasi Harmony Audio driver V0.9a, h/w id 20, rev. 18 at 0xf0104000, IRQ 82
eth0: link ok.

Stanice nemá CD-ROM, takže jsem využil možnosti netboot instalace. Na ftp Debianu a Gentoo jsem našel instalační obrazy. V BIOS konzoli nabootujete přes LAN a pak už instalace ala debian. Zkousel jsem i Gentoo, ale rychlost kompilace byla zoufala...

Rychlost GNU/Linuxu je uspokojivá, i když by mohla být lepší, docela mě mrzí, že se mi nepodařilo (zdravím hotline HP) sehnat HP-UX 10.20, který je pro tuto stanici nativní a dokáže z ní vyždímat maximum.
Pokud si chcete zkompilovat vlastní jádro, musíte si stáhnout verzi z CVS projektu PA-RISC Linux, vanilla z kernel.org nejde zkompilovat (vysvětlení viz odkaz).