Logování SMART událostí v disku. (vyřešeno)

Pokouším se přesvědčit moje SSD, aby logovalo události. Hlavně krátké a dlouhé testy. Podle smartctl -a /dev/sda by mělo mít Error logging supported. v jedné části a v druhé má napsáno Not supported
Model Family:     SandForce Driven SSDs
Device Model:     OCZ-AGILITY3
Serial Number:    OCZ-3W17E1197QC92G7L
LU WWN Device Id: 5 e83a97 e1d7c54f9
Firmware Version: 2.25
User Capacity:    120,034,123,776 bytes [120 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS, ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Apr 25 01:19:01 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x02) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  48) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x0021) SCT Status supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   117   050    Pre-fail  Always       -       0/159093951
  5 Retired_Block_Count     0x0033   100   100   003    Pre-fail  Always       -       1
  9 Power_On_Hours_and_Msec 0x0032   087   087   000    Old_age   Always       -       12172h+59m+01.250s
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       56
171 Program_Fail_Count      0x0032   000   000   000    Old_age   Always       -       1
172 Erase_Fail_Count        0x0032   000   000   000    Old_age   Always       -       0
174 Unexpect_Power_Loss_Ct  0x0030   000   000   000    Old_age   Offline      -       39
177 Wear_Range_Delta        0x0000   000   000   000    Old_age   Offline      -       5
181 Program_Fail_Count      0x0032   000   000   000    Old_age   Always       -       1
182 Erase_Fail_Count        0x0032   000   000   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0022   128   129   000    Old_age   Always       -       128 (0 127 0 129 0)
195 ECC_Uncorr_Error_Count  0x001c   120   120   000    Old_age   Offline      -       0/159093951
196 Reallocated_Event_Count 0x0033   100   100   003    Pre-fail  Always       -       1
201 Unc_Soft_Read_Err_Rate  0x001c   120   120   000    Old_age   Offline      -       0/159093951
204 Soft_ECC_Correct_Rate   0x001c   120   120   000    Old_age   Offline      -       0/159093951
230 Life_Curve_Status       0x0013   100   100   000    Pre-fail  Always       -       100
231 SSD_Life_Left           0x0013   100   100   010    Pre-fail  Always       -       0
233 SandForce_Internal      0x0000   000   000   000    Old_age   Offline      -       8707
234 SandForce_Internal      0x0032   000   000   000    Old_age   Always       -       11417
241 Lifetime_Writes_GiB     0x0032   000   000   000    Old_age   Always       -       11417
242 Lifetime_Reads_GiB      0x0032   000   000   000    Old_age   Always       -       10742

SMART Error Log not supported

SMART Self-test Log not supported

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
hledám jestli se nějakým flagem smartctl logování nezapne, ale zatím to mi nejde. Jde to nějak nahodit? připadá mi divné, když by nešlo.
Dotaz: Logování SMART událostí v disku.

Odpovědi
